【High Brightness&High Visibility】High Power LED Chips+Reflector+Clear Lens,Up 10000lm for 2 lens.Super Focus Beam,Increase 200% Brightness Than Bi Xenon Projector lens,300% Brightness than LED Bulb,500% brighter than halogen lamp. Range up to 300-500m.

657 posts · Joined 2019. #2 · Dec 27, 2019. LED bulbs shouldn't be be bothered at all by this. Depending whether they are on the CANBUS bulb minder system or not, you might get a bulb out warning which can be fixed if it occurs, but LED replacement bulbs should work fine. 2002 Ford Focus SVT, 2004 Ford Explorer Sport Trac, 2013 Ford Escape
If the low or high beam on your HID bi-xenon headlights is not working or inverted, it is most probably an issue with the polarity. Make sure the connector's pins are properly aligned. You should have 3 pins on the harness (ground, low and high beam). Release the pins and reorder them in order for the connector pins to align.
The Projector Fog Lamp. The 55w HID Bulb. TCX Ballast. Cables. Ballast and HID Connected and placed in the Fog Lamp. Note: The two thin wires seen on the Fog Lamp housing are the ones that need to be connected to the High Beam Wiring so that the Hi-Low Beams are synchronized with the High and Low Beams of the Vehicle.
2010-2015 Audi Q7 Original HID Bi-Xenon Headlight D3S Bulb Ballast ECU Controller Control Unit Wires Calbe Bulb Holder HID Projector Reflektor Bowls Lens Cover Parts,If your Audi Q7 Quattro TDI Xenon HeadLight have problem like flickering or dipped light not working then need change the parts,professional supplied by www.oemxenonshop.com Since they are very popular among thieves in my country, to prevent a recurrence I decided to buy used and install simpler non-adaptive bi-xenon headlights. According to the bmwtis schemes, I laid an additional wires from FRM3 to the headlights sockets (since they were cut at the same I wired new socket). The term bi-xenon headlight is a bit confusing, as ‘bi’ suggest two. But a bi-xenon uses just one xenon lamp for the high beam, which is then either moved or shaded each time a low beam is to My understanding was that putting $522 in the VO would at least give me baseline Bi-Xenon function (EG halogen high beams only come on as passing lights but don't come on with high beams, no CANBUS errors). Even if that's not the case, I must be doing something wrong changing the VO because it doesn't persist through a power cycle. However after approx 3 seconds, the high beam shutters close and return to low beams with a generic light warning on dash; all while stalk is still forward in “high beam on” position. Same scenario if I pull back and hold the stalk for intermittent high beam function. All the bulbs on the car work and are OEM. PhdKF.
  • f6fgmb0b7q.pages.dev/654
  • f6fgmb0b7q.pages.dev/609
  • f6fgmb0b7q.pages.dev/40
  • f6fgmb0b7q.pages.dev/782
  • f6fgmb0b7q.pages.dev/929
  • f6fgmb0b7q.pages.dev/583
  • f6fgmb0b7q.pages.dev/244
  • f6fgmb0b7q.pages.dev/140
  • f6fgmb0b7q.pages.dev/571
  • f6fgmb0b7q.pages.dev/349
  • f6fgmb0b7q.pages.dev/571
  • f6fgmb0b7q.pages.dev/504
  • f6fgmb0b7q.pages.dev/776
  • f6fgmb0b7q.pages.dev/494
  • f6fgmb0b7q.pages.dev/233

    • bi xenon high beam not working